One customer gave feedback that he cannot generate remote for his 2010 Prius using VVDI Key Tool Max Pro.

He wondered if these XM38 Xhorse Keys won't work and if he must need the Toyota Specific Xhorse XM38.

Here is the

Reason:

This remote control requires XM28/XM38 Toyota Key, while the key on the picture is XM38 Smart Key.

Solution:

Generate this remote control using XM38 Toyota.

Posted by: xhorsevvdi at 09:54 AM | No Comments | Add Comment
Post contains 81 words, total size 2 kb.

Question:

Trying to read Porsche BCM 1N35H , but always getting "chip crack failure". Components are removed , and soldering points also as shown in Xhorse VVDI PROG. Any help?

Here is the Solution:

1.CLK point seems incorrect, and it should be close to MCU

2.Trace toward crystal seems uncut

Posted by: xhorsevvdi at 09:54 AM | No Comments | Add Comment
Post contains 61 words, total size 2 kb.

Question:

I'm working on Range Rover Ir3 2007 CEM module.

Was reading information with VVDI PROG added a key with VVDI2 and write it back to CEM.

Went back to vehicle but would not start.

Note:

The marked component should be removed and a 10k resistor is required, and PCB should be restored after data reading.

Possible Solution:

Pinout is correct since VVDI Programmer reads data out, so check if the component is soldered back very well after reading.

Hope this could help!

Posted by: xhorsevvdi at 09:53 AM | No Comments | Add Comment
Post contains 96 words, total size 2 kb.

In this article, we are going to show the process of Mercedes W202 C-class 1996 AKL programming. The original only has one button.

Tools:

Orange 5

Xhorse VVDI PROG

FBS X MBE Calculator

Procedures:

Step 1.Read immo data

Remove immo box.

Connect chip to orange5 by adapter and soldering.

Read immo data.

Solder chip back to immo box.

Step 2.Generate Key File

Run FBS X Calculator.

Load immo data file.

Generate file.

Step 3.Write File to Key

Desolder key chip.

Put chip into eeprom adapter and connect adapter to VVDI PROG.

Write key file to key.

Solder chip back to key.

Remote works and car starts.

Credit to schluesseldienst_muzler_de

Done! That's how to program Mercedes W202 1996 when all key lost.

Posted by: xhorsevvdi at 09:53 AM | No Comments | Add Comment
Post contains 132 words, total size 4 kb.

One customer gave feedback that his Dolphin XP008 won't cut his keys. The cutting plate will immediately stop rotating once it touched key blank.

Here Xhorsevvdi tech shares

Reason:

XP008 is tightened by the spring.

The blank is too thick and blank touches cutting plate too quickly.

Solution:

Slightly loosen two screws, confirm machine move normally, and tighten them.

Hope this could help!

Posted by: xhorsevvdi at 09:52 AM | No Comments | Add Comment
Post contains 74 words, total size 3 kb.

One customer gave feedback that Key Tool Plus Pad will give this "Program EP failed" error when generating a XEKF20EN Super Remote. Other Super Remotes is working well, and only on this it keeps saying this.

Remote PCB:

Solution:

Update Key Tool Plus firmware to the latest version which will be available this week.

Posted by: xhorsevvdi at 09:52 AM | No Comments | Add Comment
Post contains 65 words, total size 2 kb.

One customer gave feedback that when I program the button on the box, Key Tool Max Pro does not work. He would like to change trunk button of an XM38 Toyota Key.

Here is the Solution:

Change button setting by

Selecting

Special Function>>VVDI remote function>>Toyota smart key setting

*Smart key customization is designed for NXP-smart Key

Hope this could help!

Posted by: xhorsevvdi at 09:51 AM | No Comments | Add Comment
Post contains 73 words, total size 2 kb.

Question:

The Xhorse Key Reader I received is not working properly. When I connect to reader through Xhorse App, insert a key as instructed, and start the process, it keeps telling me the device timed out and to restart the device.

Here is the Solution:

Restart Key Reader, try other options, and check if blade is inserted correctly as the prompt.

Posted by: xhorsevvdi at 09:50 AM | No Comments | Add Comment
Post contains 70 words, total size 1 kb.

One customer gave feedback that his Condor Mini Plus could not detect key and it said "Learn Fail:12 (probe detected)".

Here Xhorsevvdi tech shares

Reason:

Machine is short-circuited.

Solution:

Clean LED cover and remove metal filings inside.

Posted by: xhorsevvdi at 09:50 AM | No Comments | Add Comment
Post contains 47 words, total size 1 kb.

Question:

Xhorse VVDI Mini Key Tool, Volvo XC90 when I try to clone id48 I have this and cannot read other 7. What is problem?

Here Xhorsevvdi tech shares

Solution:

1.Pull out the key after each collection, wait some 1-2 minutes for hearing the immo relay, and continue

2.Or take out the power and put back after each collection

After every read; ignition off, battery terminal off, wait 5 seconds, battery terminal on, ignition on.

Hope this could help!

Posted by: xhorsevvdi at 09:49 AM | No Comments | Add Comment
Post contains 90 words, total size 1 kb.

Xhorse MVCI PRO J2534 Cable is a new passthru VCI supporting multiple software. So, as upgraded version of MVCI 3-in-1, what are its features over old one?

MVCI PRO vs. MVCI 3-in-1

	MVCI PRO	MVCI 3-in-1
Image
PCB
Price	99USD	89USD
Software	MVCI PRO	MVCI
Update	Online Download	CD
OS	WIN7/10/11	WIN XP
SAE J2534	√	√
D-PDU	√	×
Compatible Software	ODIS,TIS,HDS,SSM4,IDS	TIS,HDS,VIDA

The way to install software is optimized and more software is added.

Posted by: xhorsevvdi at 09:48 AM | No Comments | Add Comment
Post contains 87 words, total size 2 kb.

Xhorse MVCI PRO J2534 Passthru Cable supports multiple diagnosis software, which includes ODIS, TIS, HDS, IDS...

Here we will show you how to use it.

Software:

MVCI PRO V1.03 (e.g. with HDS V3.104)

Vehicle:

Honda Ballade 2009

Process:

Install HDS V3.104.

Install MVCI PRO V1.03.

Make sure driver is installed successfully.

Run "MVCI PRO" software.

Connect

Update and Read authorization.

Make sure software and firmware are the latest version,

Go to "Vehicle diagnosis", click car make to install passthru driver.

Run HDS, select "XH-HONDA" on "Comms Interface".

Enter vehicle info.

How To Use Xhorse Mvci Pro J2534 With Diagnosis Software 10

Diagnostic screen.

Done!

Posted by: xhorsevvdi at 09:12 AM | No Comments | Add Comment
Post contains 115 words, total size 4 kb.

With the latest update on VW IMMO4 dashboard, Xhorse MQB48 License allows user to read/ write NEC35XX immo data from 4th-generation VW.

Here is a review: read Vento immo data with key too plus ok.

Vehicle Info:

VW Vento 2016 4th IMMO system

Connect to dashboard chip and cut pin.

Key Tool Plus is calculating immo data, in this case synchronization file is not required.

Save data.

Posted by: xhorsevvdi at 09:10 AM | No Comments | Add Comment
Post contains 79 words, total size 2 kb.

Xhorse MVCI PRO J2534 Cable is designed for replacing OEM devices to complete diagnosis and programming.

Free Download Xhorse MVCI PRO J2534

V1.0.3 MVCI PRO

How to Use MVCI PRO J2534 Cable?

1.Download and install OEM diagnosis software, which is not included in the package

2.Download and install MVCI PRO J2534 software

3.Connect cable to vehicle with OEM and MVCI PRO software on computer

4.Click [Connect], software will show device information including firmware version, SN number etc.

[Read authorization] shows authorization status and available times (Note: when available times show "0", most functions will be limited)

[Update authorization] Update to the latest status and reset available times

5.Install OEM software in [Vehicle diagnosis], operate on OEM software after successful installation

6.Check version info, update software and firmware, etc. in [Upgrade]

7.Switch language, open and save logs, etc. in [Setting]

Posted by: xhorsevvdi at 09:10 AM | No Comments | Add Comment
Post contains 140 words, total size 2 kb.

Xhorse MVCI PRO J2534 is a new J2534 cable for diagnosis and programming.

Compatible OEM Software:

Support Protocols:

CAN

CAN_PS

FT_CAN_PS

FT_ISO15765_PS

ISO15765

ISO15765_PS

ISO14230

ISO14230_PS

ISO9141

ISO9141_PS

J1850PWM

J1850PWM_PS

J1850VPW

J1850VPW_PS

SW_CAN_PS

SW_ISO15765_PS

Posted by: xhorsevvdi at 09:08 AM | No Comments | Add Comment
Post contains 86 words, total size 2 kb.

Question:

The reading of VVDI Key Tool Plus doesn't show what type of chip number. For example, 4D63 shows on Key Tool Max and on the Plus, it shows 4D+ transponder.

Answer:

Wait for the update, which will be fixed in the next update.

Posted by: xhorsevvdi at 09:08 AM | No Comments | Add Comment
Post contains 55 words, total size 1 kb.

VVDI BCM2 Adapter allows us to read encrypted Audi BCM2 module without soldering. Here

we will show you how it helps Xhorse Key Tool Plus add a smart key for 2015 Lamborghini Huracan.

Read BCM2 data on bench.

Install it back and load BCM data to learn keys.

Test remote, no problem.

Posted by: xhorsevvdi at 09:07 AM | No Comments | Add Comment
Post contains 64 words, total size 2 kb.

Question:

Audi A5 2017 year, which Xhorse Remote to generate, I don't find A5 controls on the list.

Here Xhorsevvdi tech answers:

For Smart Key, use Xhorse Audi 754J Remote.

Question:

Audi A5 2017 year, which Xhorse Remote to generate, I don't find A5 controls on the list.

Here Xhorsevvdi tech answers:

For Smart Key, use Xhorse Audi 754J Remote.

Which Xhorse Remote Control To Generate For Audi A5 2017 1

The key type below is not supported.

The key type below is not supported.

Posted by: xhorsevvdi at 09:06 AM | No Comments | Add Comment
Post contains 96 words, total size 2 kb.

In this article we are going to compare two machines — Xhorse Condor Mini Plus II and Gymkana 994 — to see which one cuts Ford HU101 faster.

Make both to the screen before cutting.

Condor II slows down since it tells if it is a wrong cutter.

They both use 2.5mm cutter this time.

Hit Start buttons at same time.

They are about exact same time.

Swap Condor II cutter to a 1.5mm cutter.

Try again.

Gymkana machine finishes one side.

Condor machine with a smaller diameter cutter takes a little longer like a few seconds.

Review from One customer:

I would think that the 1.5mm would be a more accurate cut than the 2.5. Not sure if that really makes a difference if both keys work??? The real question when buying tools is reliability. I would rather have a machine that maybe doesn't cut as fast but I know that it is going to do the job each and every time

What do you think of the speed to a Key Cutting Machine?

Posted by: xhorsevvdi at 09:05 AM | No Comments | Add Comment
Post contains 186 words, total size 3 kb.

Question:

VVDI PROG has a problem when writing to a 24c02 Eeprom from a 1999 Passat ECU, It reads well but it doesn't let me write?

Here is the Answer:

Xhorse VVDI PROG cannot write this chip, or try more a few times, if it still fails, then the chip is not supported.

Posted by: xhorsevvdi at 09:04 AM | No Comments | Add Comment
Post contains 66 words, total size 1 kb.