GODIAG ECU IMMO Prog AD GT105 is a special plug-and-use connector, mainly for car communication tests, OBD short-circuit, and outside power supply.

Let's take a deeper look at this little GT105 box:

1. Help test device-car communication

When we connect our device to a car, it may prompt "No communication".

First, we should find out whether the issue happens on the car or the device, so we can connect this GT105 box to the car, and check the indicators on it.

Steps:

Connect GT105 to the car via OBD. If the power light is on, it means the car is good, so there is something wrong with the device or the device doesn't support the car.

2. OBD short-circuit

This function avoids removing ECU or immo to do short-circuit, and it applies to Ford all key lost, Mitsubishi remote match, starting VW when all key lost, Toyota immo box synchronization, etc.

Example - Mitsubishi 2016 remote match

We need to manually match the remote part after we clone the ID46 transponder and generate the remote.

Steps:

Connect GT105to the car via OBD.

Turn on the door once.

Turn on the ignition with the original key.

Press "M 1-4" to short-circuit the car.

Press the emergency light 3 times.

Press the unlock button on the new key.

Press the unlock button on the original key to complete the procedure.

3. Outside power supply

Nowhere to get power supply in some outside job?

By connecting to a car battery, it can supply power to different devices and machines.

Work with Xhorse Panda Key Cutting Machine.

Work with Key Tool Plus+ Audi BCM Solder-free Adapter.

For more info, please go to

https://www.xhorsevvdi.com/wholesale/godiag-gt105.html

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 09:22 AM | No Comments | Add Comment
Post contains 291 words, total size 7 kb.

How to add key for Mercedes Atego when all key lost. Check this blog.

We'll read the EEPROM file by VVDI PROG, and write it into a T5 transponder by Zed Full.

EEPROM: 93C86

Part 1. Read the EEPROM file

Remove the engine control unit, which has the key data.

Take out the circuit board, and desolder the EEPROM.

Put it into VVDI PROG EEPROM adapter.

On VVDI PROG, select "1-EEPROM&FLASH""ST""M93C86".

Read and save EEPROM file.

Part 2. Transponder Programming

On Zed-Full, go to "Eprom and MCU Anwendungen".

Select "Mercedes""46. Mercedes Truck - Temic ECU".

Load the EEPROM file we just saved.

Check "Key"and put a T5 ceramic chip into the coil.

Select "Programming">> "T5">> "Ok"

Success.

Program a T5 glass chip in the same way.

Test keys.

Done! That's the process of Mercedes Atego 2001 AKL Programming by VVDI Prog and Zed Full.

https://www.xhorsevvdi.com/

Posted by: xhorsevvdi at 09:21 AM | No Comments | Add Comment
Post contains 157 words, total size 5 kb.

V7.2.1VVDI2 Transponder Programmer Software is released! Get VVDI2 Transponder Programmer free download link from xhorsevvdi.com.

This V7.2.1 VVDI2 Installer only updates Transponder Programmer to V7.2.1 version. Other software version is V7.2.0, and the firmware version is V7.1.9.

https://public-cn-northwest-1-1251058331.s3.cn-northwest-1.amazonaws.com.cn/download/product/vvdi2/software/VVDI2-InstallerV721.exe

2. V7.2.1 VVDI2 Installer Update Information

Update Time: 2022-02-15

Require firmware V7.1.9

===== Transponder Programmer V7.2.1 =====

1. Improvement prepare remote function

2. Immobilizer data tool: Euro->VW->Golf 5->Visteon type

3. Bugfix

Posted by: xhorsevvdi at 09:19 AM | No Comments | Add Comment
Post contains 81 words, total size 3 kb.

Question:

To add a key for Mini Cooper 2004 when all keys are lost. I remove EWS3, read it and make a key with Key Tool Plus, the transponder started car for 2 times, and now not working. I use transponder XT27 on function immo data.

Here is the

Solution:

Use an original PCF7935 chip, and the problem will likely be solved.

Experience from locksmith colleagues:

Use good PCF7930/7931/7935. PCF7935 is expensive this days but 7930/7931 is okay. Use AS if possible. Some NXP 30/31 on Ali is defective.

Alright, we'd better have an alternative for key programming. Sometimes VVDI Super Chips work, sometimes original chips work.

Thanks to Key Car Programmation, Liudmil Docev...

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 09:15 AM | No Comments | Add Comment
Post contains 132 words, total size 2 kb.

Q: Xhorse Dolphin XP005L gave the error "Not support current data" when cutting a Jaguar FO21 Tibbe key using Clamp M3.

Here is how xhorsevvdi technicians troubleshoot:

Technicians asked for a picture of the Update Center.

Here is the screenshot.

Technicians asked him to re-update database as the arrow and try again.

The customer said same message "no support current data".

Technicians asked which cut type is the key, 6 cut or 8 cut.

This customer was cutting a FO21 8cut key.

Here is the Reason:

Dolphin XP-005L supports FO21 6-cut keys; doesn't support FO21 8-cut keys.

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:34 AM | No Comments | Add Comment
Post contains 112 words, total size 3 kb.

What's the new features of Xhorse Condor XC-MINI Plus II Key Cutting Machine?

As the upgraded version of Condor XC-MINI Plus, 'll talk about it on software and firmware.

Part 1. Software

1. Support Car, Motorcycle, Household keys

Like the new Dolphin XP005L, it supports keys beyond cars.

But anyway, it's mainly for car keys, only a few motorcycle and household keys are on the database.

2. Key Blank Engraving (Dimple key)

This is the biggest difference in my view.

Due to the two new dimple cutters (internal/external), Condor II can decode and cut multi-lock dimple keys.

Similarly, it has a key blank engraving function so that we can personalize our keys.

3. Offline Operation

Like the Condor Mini Plus, it supports offline operation. Network is not always available, so this function could be a highlight.

One thing I have to mention is that it still doesn't have a built-in battery, so if you want to take it out, you may prepare a van to power it, or conside new Dolphin XP005L.

4. Work with Key Reader

We know Xhorse Key Reader is for decoding plastic and Aluminum keys like some keys of Landrover and Audi, and it can work with Dolphin, Condor and Panda key cutting machine. Why I mention this point is that Condor XC-Mini IIis the only one that can directly connect to Key Reader without a phone.

Part 2. Firmware

1. 7-inch Touch Screen

Big touch screen control, also supports control from phone app. It should be similar to them on Dolphin II, screen and app, both work fast.

2. Clamp M5 (M1+M2)

Clamp M5 is compatible with Dolphin XP-005L and this Condor Mini Plus II. I think Clamp M5 is really handy, don't have to install and uninstall during procedure, just rotate it to select side A/B, and lots of guys also appreciate this clamp update.

Summary

I like Clamp M5 so much, so I recommend choosing between Dolphin II and Condor II.

To choose Condor II, you really need to handle dimple keys and it's hard to get a network connection;

To choose Dolphin II, you don't really need to cut dimple keys and you prefer a machine with a built-in battery so you can take it out.

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:53 AM | No Comments | Add Comment
Post contains 389 words, total size 6 kb.

VVDI2 Full version all we sell is now is with GL remote database, and free OBD read MED17 / EDC17 PIN / CS / MAC function, as well as toyota H function.

But if you bought in previous, in transponder programmer software, your database maybe China. Then you need to send us your vvdi2 SN and your country, we will change database for you.

Meanwhile, if you got the error "Decode failed! Please retry after update device! Error: E0-9C, GL remote can not use China database!", like the following pic:

Or error : Decode failed!Please retry after update!Error:80 - 9 GL remote can not use China database! the similar error info.

Please send us your vvdi 2 SN and your country, we will change database for you.

If after we change for you, still English, please try:

1. Update vvdi2 firmware to check.

2. Or please delete old vvdi2 software, then reinstall to check. You can download newest software from our page: https://www.xhorsevvdi.com/info/free-download-xhorse-software-12141.html

3. Or try this way:

1) Close VVDI and Quick Lunch
2) Delete vvdi_remote_data.bin from C:\Program Files (x86)\VVDI2\VVDI2\Transponder Programmer\DataBase
3) Connect VVDI2 to PC
4) Go to Transponder Programmer and EU data base will load automatic

www.xhorsevvdi.com

Posted by: xhorsevvdi at 08:49 AM | No Comments | Add Comment
Post contains 211 words, total size 2 kb.

Here is an interesting test about the distance that remotes response to the same car.

Compare 3 keys to see how far their remotes can control a Honda Pilot 2005.

Keys:

OEM

Another aftermarket key

Xhorse Flip Key

Let's see the comparison chart:

So, 350-400 feet, Xhorse wins.

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:44 AM | No Comments | Add Comment
Post contains 138 words, total size 3 kb.

One customer asked is it possible to connect his VVDI Mini Prog to VVDI Key Tool Plus.

If he wants to control Mini Prog from Key Tool Plus, the answer is "No", because the pad can work itself;

If he wants to transfer data from Mini Prog to Key Tool Plus via cloud storage for adding keys, the answer is "Yes", and here is the procedure:

Step 1.

After reading and saving the data file by Mini Prog on Xhorse app, go to "https://i.xhorse.com"and find the QR code.

Step 2.

On Key Tool Plus, go to

Immo Data Tool>>File management>>SCAN CODE TO LOGIN

Scan the QR code on your phone using Key Tool PlusPad.

Step 3.

On Xhorse app (phone), select

File Management>>Local file>>MINI_PROG>>Date (like 202104)

Find the data file you need, and click the ellipsis to upload it to cloud storage.

Then you can find this file in "My data". (In VVDI Key Tool Plus, VVDI Max, phone and PC)

Step 4.

On Key Tool Plus, go to

Immo Data Tool>>Area>>Brand>>Model>>EEPROM type>>download>>the file you need

Step 5.

Put a chip (OEM/VVDI Super Chip) into the key slot.

Select a key position and make a dealer key.

Done! That's how we transfer data from Mini Prog Programmer to Key Tool Plus via cloud storage.

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:40 AM | No Comments | Add Comment
Post contains 228 words, total size 5 kb.

Before we program a key, we may need to renew locked keys. Here we introduce 4 ways to renew a locked key.

Part 1. Xhorse renew cable/adapter

1)Renew cable

Work with: Mini Key Tool/Key Tool Max

Path: Special function>>remote renew>>model>>key type

Connection:

2)Renew adapter

Only able to unlock original keys.

Work with: VVDI Mini/VVDI Max/Mini Prog (require XDKP30 Adapter)

Path: Special function>>remote renew>>model>>key type

Connection:

Part 2. Hexprog renew cable+adapter

Path: Key Functions>>Key Reset>>model>>key type

Connection:

Need to solder renew cable on PCB board and then connect it to adapter and Hexprog.

Part 3. OBDSTAR X300 DP Plus

Path: IMMOBILIZER>>Renew key>>model>>key type>>

Connection:

Need to connect DP Plus Pad, renew box and adapter, and hold two pins on while it's renewing.

Part 4. KeyDiy KD-X2

Path: Chip Function>>Remote Review>>model>>chip type

Connection:

Need to clip two clamps and hold two pins on while it's renewing.

Alright, all 4 ways to renew a key, and all have their pros and cons.

Hope this could help!

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:38 AM | No Comments | Add Comment
Post contains 175 words, total size 6 kb.

Here a customer raises a question:

Tried to program C3 year 2010 with a Xhorse XNDS00EN key with the IM508 tool It failed me to double for the frequency I took the number on the side of the original key. Put it in fsk and what failed is when I do key learning.

Possible reason:

Generate the incorrect frequency option.

(The option he chose: C3 2010-2016 0523 FSK)

Solution:

Try the similar option "C3(2006-2014)0523 ASK”.

Generate Xhorse XN wireless remote by Mini Key Tool, read PIN code, and learn new keys by IM508 Key Programmer.

Customer feedback

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:36 AM | No Comments | Add Comment
Post contains 115 words, total size 5 kb.

Xhorse Toyota 8A Non-smart Key Adapter for All Key Lost No Disassembly Work with VVDI2/VVDI Max plus MINI OBD Tool and Key Tool Plus Pad. And it can support Levin, Corolla, Rav4, Pardo, Land Cruiser Prado, Camry, Highlander, Reiz, Sienna, but needs to check the fuse type, if not like the diagram, then not support.

Here is the customer review of Toyota Corolla G Chip all key lost success.

How to check your car whether supported via Toyota 8a adapter?

Please go to our page: https://www.xhorsevvdi.com/wholesale/xhorse-all-key-lost-adapter-for-toyota.html

Then check "Related Download File"

Open the photo depending on your own car model, then check the fuse whether it is the same as the diagram display, if yes, it is OK to do, or not.

www.xhorsevvdi.com

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:34 AM | No Comments | Add Comment
Post contains 137 words, total size 4 kb.

Here we're going to show you the process of how to program a VW Passat 2013 when all keys lost.

We'll desolder the chip, read it by VVDI PROG, and make a key by VVDI2 via the dump file.

Part 1. Read the chip

Firstly we desolder the 95320 chip and put it on the EEPROM socket.

On VVDI PROG Programmer app, select "1-EEPROM&FLASH" "ST"and "M95320".

Read and save the dump file.

Part 2. Prepare a new key

Enter VVDI2 transponder programmer, enter "Immobilizer Data Tool".

Select "Euro" "VW" "Passat".

For comfort module type, we have ID48 or HITAG.

We don't know it is ID48 or ID46, so we choose the first: Comfort ID48 - 95320.

Then we load the dump file, and it will give us an error if the type is incorrect.

We've got the PIN code and key information, so the type is right.

The select key position put a new ID48 chip in the key slot, and select "Make Dealer Key".

As the prompt, save the new file because we need to write it back.

Back to VVDI PROG Toolapp,

Open the new file and write it back to the module.

Part 3. Verify the chip

Back to VVDI2 Full transponder programmer,

Load the new file.

Here we can see the 4th key is already occupied.

Then we read the key chip by VVDI Key Tool.

The key ID is exactly the same as key info on VVDI2.

Restore the module and the key should start the car normally.

Done!

https://www.xhorsevvdi.com/

Skype: xhorsevvdi.com

Whatsapp: +86-13983756354

Posted by: xhorsevvdi at 08:32 AM | No Comments | Add Comment
Post contains 269 words, total size 6 kb.