Did you have these problems below after BMW OBD Programming using Key Tool Plus/ VVDI2/ BIM Tool or other tools?

>Prompts unsupported versions and requires upgrades

>Preprocessing ok but coding loss and can't recover it

>Preprocessing is unexpectedly interrupted due to missing SWFL version

>SWFL or coding version mismatch

Here we will show you how to fix these issues using VVDI BIM Tool.

Take FEM.

BIM Tool showed SWFL Lost.

Then we will fix it using BIM Tool.

Select "Fxx/Gxx Program/ Code" and "Connect Car".

Select

Vehicle programming>>40-FEM(FEM_BODY)>>Calculate programming file

"Target istufen lev" should be the same as "Shipment".

The part in grey indicates FEM's version, and the part in orange FEM version to be programmed.

Select "Programming".

Read and clear DTCs。

Select

FEM/BDC Key Learn>>Get Key Info

Coding recovered.

Done! That's how to solve "SWFL Lost" using BIM Tool.

Posted by: xhorsevvdi at 07:30 AM | No Comments | Add Comment
Post contains 152 words, total size 4 kb.

In this article, we are going to show you how to read and edit VIN for a 2016 Mazda6.

ECU:

PY9W

Tools:

VVDI Multi Prog

GODIAG ECU GPT Cable

GODIAG GT100+

Steps:

Connect tools and cables according to bench pinouts in Multi Prog software.

Read EEPROM.

Read FLASH, but here we will only edit eeprom file.

Load eeprom backup file.

Edit VIN number.

Write eeprom back.

Switch OBD mode, and read VIN on bench using GODIAG GT100+.

The VIN is edited successfully.

Load file from pcmflash for comparison, totally same.

Write back original eeprom file.

The VIN is back.

Done! That's how to edit Mazda6 2016 VIN using Multi Prog and GODIAG Cables.

Posted by: xhorsevvdi at 07:30 AM | No Comments | Add Comment
Post contains 126 words, total size 4 kb.

One customer asked if VVDI PROG could Read EZS W220 Mask 1D69J without removing MCU.

Here are 2 ways to read W220 EIS mask 1D69J:

1)Read PWD with VVDI MB via IR

It took 1.5h but worked, same mask

2)Use VVDI EZS Adapter Set

Done!

Posted by: xhorsevvdi at 07:29 AM | No Comments | Add Comment
Post contains 57 words, total size 1 kb.

Xhorse updated its OBD and Remote Database on Aug. 13, 2024, adding Ford Ranger 2015-2022, Ford Territory 2022-, NA Seat, NA VW...

Compatible Tools:

Key Tool Plus

Key Tool Max/ Key Tool Max PRO

MINI OBD V2

Check out the details below:

OBD Database

Remote Database

Stay tuned!

Posted by: xhorsevvdi at 07:29 AM | No Comments | Add Comment
Post contains 59 words, total size 2 kb.

One customer found that there was a DTC named "Tire Pressure Monitor Malfunction" on BMW motorbike screen after 8A/ 4D key programming using Key Tool Plus or VVDI2.

Here we need VVDI BMW or VVDI BIM Tool to solve it.

Here are the steps:

Connect BIM Tool to Motorbike and PC.

Run BIM Tool software,

Select

Fxx/Gxx Program/ Code>>Auto detect>>Connect Car

Select "Vehicle programming".

The "Target istufen lev" should be the same as "Shipment Date".

We don't find a shipment code available.

Select

40-FEM(X_SLZ)>>Calculate programming file

Data marked in grey show the module version.

Data marked in Orange show the programmable version.

Select "Programming".

Select

DTCs>>Read DTCs>>Clear DTCs

Done!

Posted by: xhorsevvdi at 07:28 AM | No Comments | Add Comment
Post contains 120 words, total size 5 kb.

VVDI MULTI PROG released V34 database, adding Buick Inifiti BCM...

Free Download MULTI PROG Software

MULTI PROG Software

*Download software and update database online

V34 Database Update Info (08-08-2024):

* Fixed SPC560B40 DFLASH write exception issue

* Fix the V850 series section option write OPTB0 partition write failure problem.

* Fix the V850 series section option write PFLASH partition write failure problem.

* Fix the FX4 series options in V850 failed to set the vibration frequency in some module.

* Fix V850 D70F353x and D70F3526 options read and write PFLASH partition to 12.50% failure problem.

* Optimize the read process of FENGSHEN S30(93C46A)(x and FENGSHEN S30(93C46B)(x16)

options in [OTHER]->[DongFeng]->[DongFeng].

+ Add Infiniti BCM(MC9S12XET512) option in [IMMOBILIZER]->[Infiniti]->[Infiniti]

+ Add BUICK GL8-FIRSTLAND BCM(MC9S12DB12 (2009) option in [IMMOBILIZER]->[Buick]->[Buick]

+ Add MAGOTAN-LEW-MODULE(MC9S12XS12 option in [Other]->[VW]->[VW]

+ Add Ruichi EC35 BMS(MC9S12XDT256) option in [Other]->[SERES]->[Ruichi]

+ Add Cherokee Air Conditioning Control Panel option in [OTHER]->[JEEP-><[JEEP]

+ Add EV450 COMPRESSOR(MB91F522) option in [OTHER]->[GEELY]->[GEELY]

+ Add SAG BCM-1(MC9S12G192) option in [OTHER->[SAG]->[SAG]

+ Add AUDI Reverse Radar Module(MC9S12XEG384) option in [OTHER]->[Audi]-><[Audi]

Stay tuned!

Posted by: xhorsevvdi at 07:28 AM | No Comments | Add Comment
Post contains 183 words, total size 3 kb.

Xhorse VVDI Multi-Prog Programmer is 2nd generation of VVDI Prog Programmer. Support ECU & TCU Read/Write/Clone. Free MQB48 License and BMW Bench ISN.

For xhorse multi prog, we received cutomer feedback:

Hi
I tried to do rh850 vag dash 1401
Failed
Went to 180/180 decoding

Engineer Reply:

Try heating the chip before reading, about 50 degrees

Feedback:

heating working

http://blog.xhorsevvdi.com/how-to-solve-xhorse-multi-prog-chip-crack-failed-error-code13050001/

Posted by: xhorsevvdi at 07:27 AM | No Comments | Add Comment
Post contains 77 words, total size 2 kb.

Question:

Xhorse XSBM90GL XM38 BMW Motorcycle Smart Key, Can I use it with 8A key 433.92Mhz Bmw r1250gs 2023?

Here is the Answer:

Check out the original key, only the key type below is not supported.

http://blog.xhorsevvdi.com/is-xsbm90gl-bmw-motorbike-key-used-with-433-92mhz-r1250gs-8a/

Posted by: xhorsevvdi at 07:27 AM | No Comments | Add Comment
Post contains 47 words, total size 1 kb.

Question:

Multi Prog with XDNP24GLD80/35080 Adapter won't erase m35080. The error is "Chip crack failed! Error code: 13050001".

Here some tips for erasing M35080:

1)If tools fail to crack, try 4.5v VPP

2)If tools fail to crack, try the menu requiring 48pin adapter

3)If tool shows erase successfully but actually not, test if XDNP24 Adapter is faulty

Test if pin3/ 4/ 5 between the two chips are conductible or if resistance is only about tens of ohms

*Check out pin1 (the white point) and find other pins counterclockwise

Done! Hope this helps!

Posted by: xhorsevvdi at 07:26 AM | No Comments | Add Comment
Post contains 103 words, total size 2 kb.

One customer gave feedback that he could not find an option in VVDI PROG for 0J66D. He tried an Mercedes option but failed, wrong connection or selection?

Here is the Solution:

To read Motorola chip, select MCU instead, check out mask code in chip, and search for the specific chip type.

Then select the correct option and read chip.

Done! Hope this could help!

Posted by: xhorsevvdi at 07:26 AM | No Comments | Add Comment
Post contains 73 words, total size 2 kb.

Question:

Xhorse Key Tool Plus, whatever I click on, it said 'No get device language list'?

Here is the Answer:

Swipe up from the bottom, shut apps off, and restart

Done! Hope this could help!

Posted by: xhorsevvdi at 07:25 AM | No Comments | Add Comment
Post contains 47 words, total size 1 kb.

One customer gave feedback that there were no sound in Xhorse ESL Emulator/ ELV Emulator. He turned EIS on many times but the emulators still won't respond.

Here is the Answer:

Press the button inside using like a toothpick to switch sounds

Turn EIS on and ESL Emulator will sound if connected to power in vehicle or on bench

*There are no sounds in Mini Emulator, so just make sure data are written and emulators work well.

Done!

Posted by: xhorsevvdi at 07:24 AM | No Comments | Add Comment
Post contains 87 words, total size 2 kb.

Question:

I need a key connection diagram for Xhorse because VVDI MLB Tool doesn't want to create the dealer key for me and I can't give it an ID either. And Key Tool Plus showed notifications like "Failed! -CA" Error.

Here Xhorse tech support replies:

Unsupported type.

Check out Porsche MLB key pinouts in software, and only listed keys are supported.

Done!

Posted by: xhorsevvdi at 07:24 AM | No Comments | Add Comment
Post contains 74 words, total size 2 kb.

Xhorse MQB Adapter Set allows us to read VW MQB dashboard without soldering, but to use it with VVDI PROG, we need XDPGSOGL Cable.

Here comes a review of VVDI PROG working with MQB adapter:

Read VW Polo MQB Using Xhorse Adapters and VVDI Prog #xhorse adapters read failed fixing

Connect VVDI PROG to VW cluster using MQB adapter and XDPGSOGL cable.

Try to read dashboard but fail and software gives "Try Frequency Fail" error.

Here connect another cable from VVDI PROG to Pin FMLDO in MQB adapter, supply 3.3v power to it.

Read again and no problem.

Load dashboard data into VVDI2 and get immo data for key programming.

Done!

Posted by: xhorsevvdi at 07:23 AM | No Comments | Add Comment
Post contains 123 words, total size 3 kb.

Question:

VVDI PROG don’t have pinout for bga.

Is there a pinout for programming this MB91F469 bga for me to try?

Here are the Pinouts:

144pins

208pins

Path:

2-MCU>>FUJITSU-MB91XF>>MB91F469G

Done!

Posted by: xhorsevvdi at 07:23 AM | No Comments | Add Comment
Post contains 37 words, total size 1 kb.

One customer gave feedback that Mini Key Tool update failed.

Follow steps below to update VVDI MINI:

1)Turn off vvdi mini

2)Hold on reset button on the back and turn on vvdi mini

3)Update firmware again

Done! Hope this helps!

Posted by: xhorsevvdi at 07:22 AM | No Comments | Add Comment
Post contains 48 words, total size 2 kb.

One customer gave feedback that VVDI PROG will read VW SIMOS9.4 but Multi Prog failed.

Here is the Solution:

1)Do not connect Multi-Prog to any modules.

2)Select VW SIMOS9.4 (AM29F400BB)

3)Select Test channel>>Test channel 31

4)Test the voltage of yellow cable and check if it is 3.3V

5)Select DB44 self-check

Done! Hope this helps!

Posted by: xhorsevvdi at 07:22 AM | No Comments | Add Comment
Post contains 65 words, total size 2 kb.

One customer gave feedback that BMW IMMO Programming License is not added into his Key Tool Plus. He tried to update tablet but still no license on activation list.

Here is the Answer:

The added license is BMW Motorcycle OBD Key Learn License, which only work when these basic BMW functions are activated

Done! Hope this helps!

Posted by: xhorsevvdi at 07:21 AM | No Comments | Add Comment
Post contains 69 words, total size 1 kb.

Xhorse VVDI MLB Tool for VW Audi Key Adapter work with VVDI2, VVDI Key Tool Plus, and if you use with VVDI MLB Key, no points need. But if you use with original MLB key, it will cost points.

1. Does VVDI MLB Tool need token?

• Read the original MLB key data (without VVDI MLB Key) , will cost 200 points
• Read the original key (but have VVDI MLB Key), identify the VVDI MLB key first, and then you can avoid costing points. (One VVDI MLB key can only be identified once)
• Read data from the VVDI MLB key, no need points.

Xhorse not have MLB token to sell, and vvdi MLB key will release soon, now you can use the points which get from VVDI remote keys.

• Wire key, each key 25 points.
• Wireless remote,super remote key, each key 40 points.
• Smart Key, each key 60 points.

Posted by: xhorsevvdi at 07:21 AM | No Comments | Add Comment
Post contains 226 words, total size 3 kb.

Confirmed: Xhorse Dolphin XP005 adds the function to modify key blade size.

You have keys larger and just wish that your machine could mill down one to the size you need.

Path: Click 'Cut by Bitting'. Top right button 'Modify key'.

Here comes a review from Jason:

Tested out a KLR key. These aren't made available yet and the only source for me has been ebay. It just milled down a DAT17 to KLR specs! It's ready to be cut now! This might only be for high security keys, but it's something!

Did this with an original Xhorse Dolphin.

And you could even mill down flip keys to something you need!

Stay tuned!

Posted by: xhorsevvdi at 07:20 AM | No Comments | Add Comment
Post contains 122 words, total size 1 kb.