Xhorse condor mini plus 2 automatic key cutting machine we received feedback that:

We have a Condor Mini Plus 2 and we have a Great Wall Haval M6 2024 key we need to cut. 2 track key.

As per pictures attached.

Issue is it states use the M5 B clamp. This will not hold the key as the grooves either side will not clamp in the B clamp.

I think either the M5 A or M2 would hold it however do not know how to tell the machine to change the clamp so I can read and cut the key?

Is there a way to do this?

Xhorse Engineer Reply:

Enter 166 option, then do like the option displays.

Posted by: xhorsevvdi at 07:36 AM | No Comments | Add Comment
Post contains 135 words, total size 2 kb.

Question:

Using VVDI Key Tool Lite for unlocking a Toyota smart key. I tried to unbind the key today, the application showed that the key was unlinked, but it was not linked to the car. Maybe I’m performing the procedure incorrectly?

Here are some tips for unlock Toyota smart remote:

1.The application unlocks remote successfully only when the Red Light in Remote Blinks

2.RF430 remote is not supported

3.Unlocking may fail, please check the red light

Done! Hope this helps!

Posted by: xhorsevvdi at 07:35 AM | No Comments | Add Comment
Post contains 90 words, total size 1 kb.

One customer gave feedback that the computer won't identify VVDI MLB Tool. Also tried it on Key Tool Plus but the same result.

Here is the Solution:

To connect VVDI MLB to PC, OTG data adapter is not required.

Further feedback:

Direct connect VVDI MLB to PC or Key Tool Plus, not connection on software.

Solution:

Just use this white USB cable

If you still do not know how to connect VVDI MLB, please check user manual below:

https://www.xhorsevvdi.com/upload/pro/24063017198014759460.pdf

Done!

Posted by: xhorsevvdi at 07:35 AM | No Comments | Add Comment
Post contains 92 words, total size 3 kb.

Quick Question:

VVDI Multi Prog, I’m working on a bmw cas4

I just want to write new data on it but I don’t see the write option just read

Any idea?

Here is the Answer:

Wrong option at backup, select the option for Read/ Write/ Unlock.

Done! Hope this helps!

Posted by: xhorsevvdi at 07:34 AM | No Comments | Add Comment
Post contains 58 words, total size 1 kb.

Xhorse 40-Pin Gateway Cable for Nissan Mitsubishi AKL is available now! It will work with VVDI Key Tool Max Pro and Key Tool Plus to bypass pin code for AKL programming.

Check out its Support List:

Mitsubishi Outlander 2022-

Nissan SYLPHY 2021-, B18

Nissan X-TRAIL 2021-, T33

Nissan PATHFINDER 2022-

Nissan Ariya 2023-

Nissan Altima 2019-

Nissan Qashqai 2017-

Connection Diagram:

Order Now: https://www.xhorsevvdi.com/wholesale/xhorse-xdkp91gl-40pin-connector.html

Read Also:

http://blog.xhorsevvdi.com/xhorse-nissan-1632-40-pin-adapter-support-list/

Posted by: xhorsevvdi at 07:34 AM | No Comments | Add Comment
Post contains 77 words, total size 2 kb.

Here comes a review of VVDI Multi Prog working on Audi tcu:

Multi Prog read and write success Audi 2014 SQ5 8hp55a

Read original module twice and compared data all ok

Read doner module and saved files

Wrote doner module then read doner module and compared to original read all good to go

No component protection to do once fitted as it thinks it's the original gear box . Also in some cases the OEM will not allow a second hand unit to be adapted to a vehicle with there software

Done!

Posted by: xhorsevvdi at 07:33 AM | No Comments | Add Comment
Post contains 102 words, total size 1 kb.

Question:

Trying to cut a 2018 Lincoln key but it’s not listed in Dolphin XP005.

Here is the Answer:

Select any Ford or Lincoln with Hu101 10-cut,

Or select under the menu Aviator.

Good to know:

Do not select the vehicle, just select the make and then all key blanks, then we have all the options, much faster that way when we already know the key blank we are looking for.

Done! Hope this helps!

Posted by: xhorsevvdi at 07:33 AM | No Comments | Add Comment
Post contains 83 words, total size 1 kb.

Question:

VVDI Multi Prog, trying to read Porsche SDI10.2 ECU by the guidance, but it doesn't show any pictures of ECU in boot mode. There are no instructions for boot mode on the board? I need something like this, basically there is no board layout for boot mode in the software. Do you know which wires to connect to those points? There is nothing in the software.

Here is the Pinout in Boot mode:

White - P3

Blue - P6 P7 P8 (No order)

Also do not forget Bench wiring.

Done! Hope this helps!

Posted by: xhorsevvdi at 07:32 AM | No Comments | Add Comment
Post contains 106 words, total size 2 kb.

Quick Question:

VVDI MLB Tool does not work. It cannot be bound / activated?

Here Xhorsevvdi tech support answers:

Activate VVDI MLB by the path below.

Path: Immo programming>>More function>>Test function>>test function 8>>sub test function 58

Done!

Any questions, contact us!

Posted by: xhorsevvdi at 07:32 AM | No Comments | Add Comment
Post contains 48 words, total size 2 kb.

Here comes a review of VVDI Multi Prog cloing J518 module from Audi A6 2010.

Another one J518, this time from Audi a6 2010 year, successfully cloned with Multi Prog.

Need to adjust VDD voltage manually 4.5V to crack and read/ write chip. 3L40K chip.

Sometimes won't crack and read chip on default 2.5v.

Posted by: xhorsevvdi at 07:31 AM | No Comments | Add Comment
Post contains 64 words, total size 2 kb.

Quick Question:

Trying to adjust the signal strength of this VVDI Remote using Key Tool Max.

Can’t go into Toyota smart key settings doesn’t support. Car is 8a-land cruisers BA.

Here Xhorsevvdi tech support answer:

lf no proxy or weak signal after programming, adjust customization 4 (default is 1, maximum is 20)

Path: Special function >>VVDl remote function >>Smart key customization

Done! Hope this helps!

Posted by: xhorsevvdi at 07:31 AM | No Comments | Add Comment
Post contains 73 words, total size 1 kb.

One customer gave feedback that VVDI Multi Prog failed to read ME17.9.64.

Multi Prog has the ECU option but the pinout is not good.

Tried with the pinout on pcmflash and the tool read perfectly.

Hope this could help!

Posted by: xhorsevvdi at 07:30 AM | No Comments | Add Comment
Post contains 48 words, total size 1 kb.

Quick Question:

Xhorse MVCI PRO trying cable to read my Subaru. I installed MVCI Pro 2.1.4 and SSM4 on different Win10 computers but cannot communicate. The cable is green but not blinking. The MVCI Pro program finds the cable and I installed the Subaru driver from it but it does not work. The weird thing is that it detects the cable with firmware version V1.6.2 and the latest version is V1.3.0. What is the reason for this please?

Here Xhorsevvdi tech support answer:

Uninstall and then try to install "J2534PageInstallerSubaru". (Click to download)

SSM3 is supported, while SSM4 may not be.

Done! Hope this helps!

Posted by: xhorsevvdi at 07:30 AM | No Comments | Add Comment
Post contains 114 words, total size 2 kb.

One customer asked about how to replace the Xhorse VVDI2 battery. A notification appears asking to change a battery.

Here Xhorsevvdi tech support answers:

Open VVDI2, replace battery (CR2032), update tool, and it will be fine.

*Remember to use an external supply before and during removing battery

Make grey cable positive, white negative, solder a battery to vvdi2 before removing old battery, and then remove old one and solder a new one

Done! Hope this helps!

http://blog.xhorsevvdi.com/how-to-solve-vvdi2-the-device-battery-is-lower/

Posted by: xhorsevvdi at 07:29 AM | No Comments | Add Comment
Post contains 86 words, total size 2 kb.

VVDI MULTI PROG released V30 database, adding ST SPC57XX, FUJITSU MB96FXXX...

Free Download MULTI PROG Software

MULTI PROG Software

*Download software and update database online

V30 Database Update Info (2024-07-05)

* Update the option EIS-W639-3K853 wiring diagram
* Update the option SAG BCM-1(MC9S12G12 and Sino Trunk BCM-1(STM8AF52AA) wiring diagram
* Fix the DJ3 and DL3 series options in V850 failed to set the vibration frequency in some module
* Fix the crack failure issue of HC908AZ60A_FLASH_SECURED option in <MCU>-><Motorola>->< MC68HC(9)08 Series>
+ Add GL8 13 KEY(2006) option in <IMMOBILIZER>-><Buick>-><Buick>
+ Add FOCUS DASHBOARD(D70F3425) option in <DASHBOARD>-><Ford>-><Ford>
+ Add Baleno BCM(R7F701623) option in <OTHER>-><Suzuki>-><Suzuki>
+ Add Hyundai BCM(R7F70164 option in <OTHER>-><Hyundai>-><Hyundai>
+ Add VW Passat Gateway Module(D70F3433) option in <OTHER>-><VW>-><VW>
+ Add M350803, M350806, M35080V6, M35080VP options in <Serial EEPROM&FLASH>-><ST>-><M35XXX>
+ D80, D160 options in <Serial EEPROM&FLASH>-><ST>-><DXX>
+ Add R7F0C001G, R7F0C001L, R7F0C002G, R7F0C002L, R7F0C014B, R7F0C014L, options in <MCU>-><Renesas>-><RL78-R7F0XX>
+ Add SPC570S40, SPC570S50, SPC572L64, SPC574K72, SPC574S60, SPC574S64 options in <MCU>-><ST>-><SPC57XX>
+ Add MB96F313A/R/Y, MB96F315A/R/Y, MB96F326A/R/Y, MB96F336U, MB96F338R/U/Y, MB96F343D/F, MB96F345D/F, MB96F346A/R/Y, MB96F347A/R/Y, MB96F353A/R, MB96F355A/R/Y, MB96F356A/R/Y, MB96F378C/H/T, MB96F379R/Y, MB96F385R/Y, MB96F388H/T, MB96F389R/Y, MB96F395R/Y, MB96F612A/R, MB96F613A/R, MB96F615A/R, MB96F622A/R, MB96F623A/R, MB96F625A/R, MB96F633A/R, MB96F635A/R, MB96F636R, MB96F637R, MB96F643A/R, MB96F645A/R, MB96F646R, MB96F647R, MB96F653A/R, MB96F655A/R, MB96F656R, MB96F657R, MB96F673A/R, MB96F6B5A/R, MB96F6B6R, MB96F6C5A/R, MB96F6C6R, MB96F8D3K3/4, MB96F8D3KD/E/F/U/V/W, MB96F8D5K3/4, MB96F8D5KD/E/F/U/V/W, MB96F8E3K3/4, MB96F8E3KD/E/F/U/V/W, MB96F8E5K3/4, MB96F8E5KD/E/F/U/V/W options in <MCU>-><FUJITSU>-><MB96FXXX>

Stay tuned!

Posted by: xhorsevvdi at 07:29 AM | No Comments | Add Comment
Post contains 223 words, total size 4 kb.

VVDI MLB Tool is a professional tool in key adding for MLB Models of VW, Audi, Porsche...

This article is a tutorial on how to use this tool with Key Tool Plus/ VVDI2.

Part 1. VVDI MLB Tool + VVDI2

1.Calculate key data

Connect VVDI2 to VVDI MLB, with "TOP" side upwards.

Put original key on sensing area.

Turn on VVDI MLB Tool software.

Select "Identification key" to identify original key.

Select "Collect key data" to calculate key data.

Select "Make Dealer Key" and load key data.

2.Key Learn

Turn on ignition.

Connect vehicle to VVDI2.

Put key close to sensing area.

Turn on VVDI2 software.

Select

Audi>>Key learn>>MLB Immobilizer system

Select "Read vehicle information".

Select "Key learning" and load data.

Key learn complete.

Part 2.VVDI MLB Tool + Key Tool Plus

1.Calculate key data

Connect Key Tool Plus to VVDI MLB.

Turn on Key Tool Plus,

Select

Immo programming>>Audi>>Select by type>>MLB immobilizer systems

Select "1-Identification key" to identify original key.

Select "2-Connection diagram".

Select "3-Collect key data" to calculate key data.

Select "4-Make Dealer Key" and load key data.

2.Key Learn

Connect vehicle to Key Tool Plus.

Put key close to sensing area.

Select "5-Learn Key" and load key data.

Key match complete.

Done! That's how to use VVDI-MLB Tool.

Posted by: xhorsevvdi at 07:29 AM | No Comments | Add Comment
Post contains 219 words, total size 5 kb.

One customer wondered if VVDI MLB Tool needs tokens or points for data calculation.

Here is the Answer:

1.Read data from OEM key (No VVDI MLB Key): 200 points

2.Read data from OEM key (with VVDI MLB Key): No points

*Identify new VVDI key first, and then read OEM key

3.Read data from VVDI MLB Key: No points

Done! Hope this helps!

Posted by: xhorsevvdi at 07:28 AM | No Comments | Add Comment
Post contains 71 words, total size 1 kb.

One customer asked how to clone BCM gj32-14f041-ab using VVDI Multi Prog. The car is Landrover 2013. Tried to read eeprom but all FF.

Here are some tips:

For this BCM, no eeprom only D-flash.

To clone it, read write D-flash and P-flash (VIN inside)

Done! Hope this helps!

Posted by: xhorsevvdi at 03:22 AM | No Comments | Add Comment
Post contains 60 words, total size 1 kb.

Quick Question:

My Mini Key Tool is unable to generate XM38-Toyota Remote any advice I will appreciate

Here is the Answer:

Make sure VVDI Mini is connected to Wi-Fi/ hotspot.

Remote controls marked with "Online" requires network connection.

*to generate controls marked with "Cloud", users need Key Tool Max (PRO)/ VVDI2

(Details: http://blog.xhorsevvdi.com/vvdi-key-tool-generate-cloud-remote-control-tips/)

If the tool is already network-connected, make sure battery is brand new.

Feedback:

the problem was the battery, Now generate successfully

Done! Hope this helps!

http://blog.xhorsevvdi.com/solved-mini-key-tool-unable-to-generate-xm38-toyota-remote/

Posted by: xhorsevvdi at 03:22 AM | No Comments | Add Comment
Post contains 89 words, total size 2 kb.

Question:

ForthebladeSIP22(fiatducato)Condor MINI PLUS IIisnotdecodingcorrectly. What I should do?

For HU83, thedecodingisdifferentthanthekey.

Here is the Solution:

1)Perform cutting calibration again

2)Check if shoulder align is correct

3)Make sure used cutter is the same as that in settings

In this case, the problem is the used HON66 in cutting calibration.

Use a new HON66 blade in cutting calibration as required, and Condor II Machine should decode well.

Done! Hope this help!

http://blog.xhorsevvdi.com/solved-condor-mini-plus-ii-fail-to-decode-hu83-hu92r/

Posted by: xhorsevvdi at 03:21 AM | No Comments | Add Comment
Post contains 81 words, total size 3 kb.