VVDI 35160 Chip supports ST chips including 35080XX,35160XXX. D80 D160 35080 35160 are supported while 35128 is not included.

Here is how to use Xhorse 35160 chip with VVDI PROG on the latest v5.1.4 software.

Without Adapter.

With Adapter.

Procedure:

Note: If red dot is already on dash, it will remain after procedure ends

1)Read Original Chip

Select the chip type, click "All”, Read and Save original 8-pin chip data

In old version, "All”data was divided into 3 partitions.

2)Replace VVDI Chip

Select chip type same as the original, and write the data file to VVDI chip (VVDI 35160 chip will automatically generate chip)

If we need to correct odometer, click "Erase INC", then the first 2 lines will be erased (all "00”). Manually enter odometer, then click "Write", operation completed.

3)Verify Dash

Solder the edited chip back to dash, and check if the dash works.

http://blog.xhorsevvdi.com/vvdi-prog-v5-1-4-35160-chip-guide-with-without-adapter/

Posted by: xhorsevvdi at 10:30 AM | No Comments | Add Comment
Post contains 155 words, total size 3 kb.

One customer asked how to sort a problem with a moving chip in Xhorse Wire Keys. Sometimes he can’t start a Mazda 6 2008 because of this problem.

Here we shares some locksmith fellows’choices:

Review 1

Super glue or masking tape.

Review 2

Paper glue is perfect for the job.

Review 3

Used to use the locktite brand blue putty, but I found that the gorilla glue version works better. super cheap. works great, holds chip where u want, and u can still take the chip out if u want.

Review 4

Blue Tack.

Posted by: xhorsevvdi at 10:29 AM | No Comments | Add Comment
Post contains 104 words, total size 2 kb.

One customer wondered that why there were still some functions unlicensed on Xhorse VVDI2 since he bought a full-version one.

For VVDI2 full, depends on the time you bought,it may has different authorization in your vvdi2. Before 2017 year, VVDI2 not release ID48 96bit, ID48 OBD II, FEM,Toyota h. Your vvdi2 full all activated at that time. But after the new authorization release, your vvdi2 full new authorization not activated.

Solutions:

1)Contact us and attach device’s Serial Number, we’ll check if it’s a full-version one or activate unlicensed functions.

2)If it is a Full-version VVDI2, but the software interface still doesn’t change,

Update the firmware to the latest version and check again.

3)If the interface still remains,

Just try these unlicensed functions. They may work normally but display incorrectly.

4) Or you can check in vvdi2 quick start tool>>update>>device info to check, but before check, please update firmware to check firstly,then check.

5) If you bought before 2017 year, new VVDI2 authorization not activated, you need:

5.1 Toyota H can get free by yourself.

5.2. MQB, if you vvdi2 bought after 2019 year, we can help you activate free. If before 2019 year, need to purchase ID48 96bit to get MQB.

5.3. ID48 96bit, ID48 OBDII, BMW FEM authorization need to purchase to activate. Thanks

Posted by: xhorsevvdi at 10:28 AM | No Comments | Add Comment
Post contains 222 words, total size 3 kb.

In this article, we’ll show you all Xhorse VVDI universal remotes and their functions.

Generally, Xhorse has released 4 types of universal remotes:

XK Wired Remote, XN Wireless Remote, XE Super Remoteand XS Smart Remote.

Apart from regular designs, there are novel types like King Card, Smart Watch and Garage Remote.

1. VVDI XK Ranges

• Wired universal remote, no risk in programming
• Cloneable for some old model car
• Reprogrammable

*Garage Remote

• Cloneable for garage remote
• Compatible with dozens of garage door brands
• More than pretty, easy to use

2. VVDI XN Ranges

• Built-in cloneable transponder
• Support simulation of multiple immobilizer transponders including 11/12/13/7936/ 7937/7947XTT/7946 etc.
• Original NXP immobilizer transponder
• Wireless programming; Reprogrammable

3. VVDI XE Ranges

• Universal wireless remote with an embedded cloneable Super Transponder
• Support generating various wireless remote types including 11/12/13/7935/7936/48/4C/4D/4E/8A/8C/8E etc.
• Integrated design, ultra-stable and reliable
• Wireless programming; Reprogrammable

4. VVDI XS Ranges

• Support simulation of multiple immobilizer transponders including 46/47/48/49/4A/MQB etc
• Generate and program prox key
• Support a variety of car models
• Wireless programming; Reprogrammable

*SW007 Smart Watch

• A watch works as a car remote
• Designed by Xhorse and manufactured by FIYTA with over 30 years of experience in mechanical watches
• Support the same car models as XS series universal smart key
• Durable buttons; long service life; 5ATM water-resistant

*King Card

• One of a kind: card-shaped smart key with only 5mm thickness
• Support the same car models as XS series universal smart key
• Rounded design with compact feel
• Sensitive button with long service life

XM Toyota Smart

• Built-in XM38 or XM28 transponder
• Support only Toyota smart key
• Wireless programming; Reprogrammable
• No need bonus points to generate
• No reward points, please note this

Read also:

https://www.xhorsevvdi.com/info/buy-xhorse-vvdi-remotes-to-get-bonus-points.html

Posted by: xhorsevvdi at 10:27 AM | No Comments | Add Comment
Post contains 284 words, total size 7 kb.

Xhorse KEY READER is a professional and portable key identification to identify car keys (including plastic keys and aluminum keys) quickly and accurately.Users can obtain the precise key bitting results and cut keys directly via Xhorse APP and key cutting machines of Xhorse.

And we received feedback that read benz hu64 key not OK:

This key reader is not working properly, see original key on bottom, the scan did not work well

Not reading correctly

This is from scan

Engineer suggestion:

Use the wrong option, please try HU64-2 or -3.

Posted by: xhorsevvdi at 10:27 AM | No Comments | Add Comment
Post contains 100 words, total size 2 kb.

In this article, we’ll show you what optional adapters VVDI MB has and their function.

We’ll cover:

1. NEC Key Adaptor

2. EIS/ESL Test Line Cables

3. W204 ELV adaptor

4. Power Adapter

5. ELV Emulator for Benz 204 207 212

Let’s see VVDI MB Adapters:

Adapter Name	Price (USD)	Adapter Image	Function	Connection
NEC Key Adaptor	100$		1.v51 v57 get password 2.normal key/keyless go renew/write key file by IR
EIS/EL Test Line Cables	119$		EIS/ELV Test Line for W164 W166 W204 W205/W222 W212 W221 ISM 7-G
W204 ELV adaptor	105$		Renew Benz W202/W204/W212 Broken ESL
Power Adapter	129$		FBS3 gateway simulation, reduce key password calculation time, reduce IR adapter plug in&out times, etc.
ELV Emulator for Benz 204 207 212	64$		Emulate Benz W204/W207/W212 ESL

Where to get VVDI MB at the best price?

VVDI MB: https://www.xhorsevvdi.com/wholesale/xhorse-vvdi-benz-vvdi-mb-bga-tool.html

VVDI MB+1 Year Token: https://www.xhorsevvdi.com/wholesale/vvdi-mb-bga-tool-one-year-token.html

More adapters or bundle packages, contact us.

https://www.xhorsevvdi.com/

Posted by: xhorsevvdi at 10:26 AM | No Comments | Add Comment
Post contains 156 words, total size 5 kb.

Xhorse Condor MINI Plus ii is the newest xhorse key cutting machine, and we received feedback that get the error:

Error Code:20

Spindle motor abnormal, rotate speed can not up to rated value

The error pic just like the follow pic:

Please do Spindle Motor Test

Engineer solution:

Please remove the resistor from the driver PCB.

Or contact your seller you bought from to get a new drive board. But no matter which way you choose, you have to remove and disassemble.

www.xhorsevvdi.com

Posted by: xhorsevvdi at 10:25 AM | No Comments | Add Comment
Post contains 91 words, total size 3 kb.

Question:

PCF79XX Adapter, plus VVDI PROG can’t read BMW F-Series Remote 434m-in-circuit. The chip is PCF7953.

Even desolder the chip to eeprom adapter, still not connected.

Here Xhorsevvdi engineer gives the

Solution:

1)When desoldering the chip to eeprom adapter, try different positions

2)If still not connected, try with PCF79XX Adapter:

Remove the battery, exchange two soldering pins marked (red&black line) on PCB.

Posted by: xhorsevvdi at 10:25 AM | No Comments | Add Comment
Post contains 75 words, total size 2 kb.

Here is a review of Xhorse VVDI MB Tool: 2008 Mercedes CL500 key programmed with fast MB Power Adapter to read password in 18 minutes.

EIS Tool:

Here is the procedure:

Step 1. Password Calculation

Select OBD Mode, lost all working key, and w204 fast mode.

Click "Data Acquisition”to start password calculation.

Here we use free token, since we have an Xhorse Key Cutting Machine.

Around 18 minutes later, we have the password.

Step 2. Read EIS

Read and save EIS data.

Step 3. Prepare Key

Load EIS file we just saved.

Paste password we just got.

Select key postion and "v051”to prepare dealer key.

Step 4. Add Key

Identify BE key.

Since it’s an used key, so we erase it.

Load key file.

Paste key password and write key.

Start the vehicle no problem.

Posted by: xhorsevvdi at 10:24 AM | No Comments | Add Comment
Post contains 148 words, total size 5 kb.

Question:

Programmed 2 keys for Mazda 3 2014 manual transmission(all key lost) after that red light is on (keyless system error). 2 keys working properly (car is starting and remote is working).

Clear dtc doesn’t work. FCC WAZSKE13D01.

Reason:

With Mazda PTS you have to have the same type of smart key for both of them as the original

Here Xhorsevvdi engineer shares several

Solutions:

1. Match FCC, IC numbers, and even number of Buttons

If it’s 3 buttons both got to be 3 buttons; if it’s 4 buttons both got to be 4 and they have to be like the original one

2. Try WAZSKE13D02 smart keys

3. Repair by programmers

Take Xhorse as an example,

If we program Mazda by Xhorse Smart Key, we can repair mazda key light by VVDI Key Tool Max, VVDI Mini Key Tool, etc. via

Special Function>>Mazda ID 49 smart key light repair

An original key is required.

4. Original key close enough when immo light flash

With at least 1 original key registered, after we program it, the immo light will begin to flash, where we must bring it closer and warning light will change from flashing read to staying solid green.

Hope this could help!

Posted by: xhorsevvdi at 10:23 AM | No Comments | Add Comment
Post contains 215 words, total size 4 kb.

In this article, we’ll show you the difference of 1st-generation and 2nd-generation Xhorse XM Toyota Smart Key.

Let’s see their difference:

XM Toyota Smart Key	XSTO00EN XM28	XSTO01EN XM38
Image
IMMO Type	8A/4D	8A/4D/4A
Reprogrammable/Cloneable	Yes	Yes
Key Shell	No	Yes
Compatible Device	Key Tool, VVDI MINI Key Tool, Key Tool Max, Key Tool Plus, VVDI2	Key Tool, VVDI MINI Key Tool, Key Tool Max, Key Tool Plus, VVDI2
All Key Lost/Add Key	Yes	Yes
Emergency Start	Yes	Yes
Board Number	0020 3370 6601 0111 2110 5290 0031 0310 0182 7930 A433 0030 3330 7980 F433 0010(-part) F43 0780 0140	0020 F43 7980 0140 0031 0120 0011 3410 6221 3450 2110 3370 6601 0111 0091 0410 0010 2000 6230 0351 0182 5290 A433 0310 5380 0040 0330 0500 4610 0780 3330 7930 F433 0030 5300
Frequency	312, 315, 314, 433MHz 8A: 312.10/314.35 314.00/315.10 314.35/315.10 312.50/314.00 433.92 433.57/434.41 4D: 315.12 312.50 433.92 314.35 314.00	All 312MHZ-434MHZ Dual: 312.10/314.35 314.35/315.10 312.50/314.00 314.00/315.10 433.57/434.41 Single: 315.00 315.10 315.12 314.35 312.50 314.00 433.92
Vehicle	Toyota: Camry (08-17) RAV4 (08-19) Corolla (08-1 LEVIN (-1 Land Cruiser (08-20) Highlander (09-19) Crown (10-17) REIZ (08-12) Alphard (-12) SIENNA (05) Previa (07-) WISH (1 E'Z (-15) VIOS (08-13) Land Cruiser/Prado (08-20) Toyota86 (12-14)Lexus: GS300 (13-17) ES300 (13-17) GS400 (13-17) GS430 (13-17) IS200 (13-17) IS300 (13-17) ES330 (13-17) RX270 (14) CX460 (10) CT200 (15) NX200 (16-) RX450 (15-)BRZ (-14)	Toyota: Camry LEVIN Highlander SIENNA E'Z Avalon RAV4 PRADO Crown Previa VIOS CHR Corolla Land Cruiser Alphard WISH REIZ IZOA Prius Vellfire Wildlander Lexus: GS IS ES RX CX CT NX RC LC LS LX LM

Read also:

How to know XM28 and XM38 Toyota Smart Key?

New Xhorse XM38 Toyota Smart Key Intro

New Xhorse XM38 Toyota Smart Key in stock now!

https://www.xhorsevvdi.com/wholesale/xhorse-xsto01en-xm38.html

https://www.xhorsevvdi.com/

Posted by: xhorsevvdi at 10:23 AM | No Comments | Add Comment
Post contains 304 words, total size 6 kb.

New XM38 Toyota smart key add key for all key lost requires data collection and calculation, and now you can use the VVDI Key Tool Plus to connect to the Internet for data processing to generate keys. This function needs to collect data from the ECU on the vehicle, the original OBD 8A Adapter cannot perform this function, it needs to be equipped with this new Xhorse 8A smart adapter.

Xhorse XDBASK Toyota 8A Smart Key Adapter is divided into two parts:
Transfer adapter and cables. The smart authentication unit 89990 on the new smart Toyota has two types of plugs, so the connector is divided into: TOY-C1 TOY-C2. Compared with the car's IMMO box (ID code box), the location of the intelligent authentication unit is easier to find and operate. No worry about the complicated operation and disassembly when adding keys.

Xhorse XDBASK Toyota 8A Smart Key Adapter Connection Diagram

Now we will introduce how to connect Xhorse XDBASK Toyota 8A Smart Key Adapter
Xhorse XDBASK Main Adapter

And two connector cables
The connector cable is divided into: TOY-C1 TOY-C2
depends on the new smart Toyota ECUtyes

After we choose TOY-C1 or C2
We connect the little connector from C1 or C2 with Main Adapter

Main Adapter power port no need connect anything

Then, Main Adapter insert on key tool plus

Use KeyTool Plus main test cable connect with Main Adapter another side

and KTP main cable OBD connector connect with car OBD

TOY-C1 or C2 connector connect with car ECU

After all connect well
You can do the data collecting

Posted by: xhorsevvdi at 10:22 AM | No Comments | Add Comment
Post contains 277 words, total size 4 kb.

Xhorse XSTO01EN for Toyota XM38 Smart Key English GL version is new released item, and it is with enough stock!

And we received feedback that when use VVDI Key Tool max generate Toyota XM38 smart, get the error like the following pic:

Remote Program
Calculate failed(error code:Error:9B),please collect and retry!

Forthosewhoalreadyusedxm38series

And we check the PCB, it is XM38

The PCB is same like the one XM38

Suggestion from Engineer:

It is the Key Tool Max and XM38 version not match. If use GL KeyTool Max, Please use English Toyota XM38 smart key, not use CN version.

www.xhorsevvdi.com

Posted by: xhorsevvdi at 10:21 AM | No Comments | Add Comment
Post contains 108 words, total size 3 kb.

New Xhorse Dolphin XP008 Key Cutting Machine is designed for Bit Key, and it is a specific manual machine for Special Bit, Double Bit Keys.

What Keys can Dolphin XP-008 Cut?

Bit/Pump Keys.

Common Bit Key covers treasury key, ATM key, bank deposit box key, padlock key, etc.

Dolphin XP008 Advantages:
All-purpose Clamp

0-45°Rotation Bench

Built-in Lithium Battery

Easy to Carry

If you are interested in this new Dolphin XP008, please check:

https://www.xhorsevvdi.com/wholesale/xhorse-dolphin-xp008.html

Posted by: xhorsevvdi at 10:21 AM | No Comments | Add Comment
Post contains 81 words, total size 2 kb.

Question:

Ford 2016 ranger AKL have VVDI Key Tool Plus double flasher keeps flashing and can’t communicate.

Reason:

The active alarm is on, needs to disable alarm firstly before programming.

Solution:

To disable Ford alarm, generally ways are different for -2015 and 2016- Ford.

1)For 2016- Ford models, use Xhorse Ford AKL Cable to deactivate alarm firstly.

2)For -2015 Ford models, wait 10 minutes until hearing the beep, which means the alarm is disabled.

Step 1.

Press unlock button to deactivate the alarm. If you've misplaced remote for car, use PATS-programmed key to unlock driver's side door. Then, put the key in the ignition and turn the key to the "on" position. The vehicle's battery should be on, but the engine shouldn't be running.

Step 2.

Locate the override button on the alarm box, beneath the driver's side of the dashboard. Press the button and hold it in until the alarm beeps one time. The LED light for the alarm should stop blinking, indicating the anti-theft system is disabled.

Step 3.

To reset the vehicle's alarm, put the PATS-programmed key in the ignition and turn the key to the "on" position. Press the override button. When the alarm resets, it chirps two times and the LED light begins blinking.

Notes:

• Ford vehicles use both an active and passive anti-theft system.
• If you've misplaced your remote for the car, use the PATS programmed key to unlock the driver's side door.

Hope this could help!

Posted by: xhorsevvdi at 10:20 AM | No Comments | Add Comment
Post contains 253 words, total size 3 kb.

Question:

If a cutter breaks on Dolphin XP005 during cutting, or it runs out of battery in the middle of a cut, Machine seems to give errors when the probe doesn’t see an uncut key.

Is there any way to continue the key after changing the cutter?

Here Xhorsevvdi gives the

Solution:

Step 1

Put a new blank of the same type for the probe to detect.

Step 2

Once the identification is complete, click "Pause”.

Step 3

Remove the new blank, put the semi-cut key back in, and click "Continue”.

Step 4

Repeat process for the other side if needed.

Same way on other Xhorse Automatic Machineslike Dolphin XP005L, Condor XC-Mini Plus...

Hope this could help!

Posted by: xhorsevvdi at 10:19 AM | No Comments | Add Comment
Post contains 128 words, total size 3 kb.