Question:

Xhorse Condor XC002 PRO Machine says E0001andsmellsabit?

Here is the Solution:

Open the back cover and tighten the two screws or loosen them if they are overtighted.

Done! Hope this helps

Posted by: xhorsevvdi at 06:49 AM | No Comments | Add Comment
Post contains 42 words, total size 1 kb.

Question:

Xhorse XDNP50 EWS3 Adapter, how to plug in this cable?

Answer:

Solder the cable as below.

Open eeprom clip, break the protective layer, and solder cable to clip.

Read Also:

http://blog.xhorsevvdi.com/xhorse-xdnp50-ews3-adapter-tutorial/

Done! Hope this helps!

Posted by: xhorsevvdi at 06:48 AM | No Comments | Add Comment
Post contains 44 words, total size 2 kb.

How to get key code when all keys are lost with Xhorse Key Cutting Machine?

Generally key code is on the key lock and we have to remove it first.

Here we will show you how.

1)Remove key lock and get key code

2)Select "All key lost" and enter key code

3)Cut key

Done! Hope this helps!

Posted by: xhorsevvdi at 06:48 AM | No Comments | Add Comment
Post contains 70 words, total size 2 kb.

One customer gave feedback that his Xhorse Key Tool Max Pro Programmer was faulty. Once he selected ignition switch coil signal detection, the tool would beep and always shows 4D.

Here is the Solution:

Update Key Tool Max Pro firmware to V1.6.5 and try again.

Make sure nothing else interfere signal.

Done! Hope this helps!

Posted by: xhorsevvdi at 06:47 AM | No Comments | Add Comment
Post contains 67 words, total size 1 kb.

Question:

Anyone has a solution for this Audi ELV of how to bypass it or simulator? VVDI PROG or VVDI2 can do it?

Answer:

1)VVDI PROG Clone Audi ESL

2)Swap the processor by soldering

Done! Hope this helps!

Posted by: xhorsevvdi at 06:47 AM | No Comments | Add Comment
Post contains 49 words, total size 2 kb.

One customer asked if Xhorse VVDI Multi Prog can be used in offline mode.

Here is how to use Multi Prog ECU Programmer in offline mode:

1.Multi prog software version 4.0 or later_: Ensure your software is up-to-date, as earlier versions might not support offline mode.

2.Offline license_: You'll need to obtain an offline license from the manufacturer or an authorized distributor. This license will enable offline mode.

3.Pre-loaded data_: Before going offline, make sure you've pre-loaded the necessary data, such as device configurations and programming files.

In offline mode, you can perform certain operations, like:

- Reading and writing device configurations

- Programming certain devices

- Checking device information

*The functions requiring server connection are not available in offline mode

Posted by: xhorsevvdi at 06:46 AM | No Comments | Add Comment
Post contains 132 words, total size 2 kb.

Question:

VVDI Multi Prog failed to read MC68HC05X32(1D69J) using the Xhorse XDNP41 Adapter, and it said "Chip power configuration Control instrument timeout".

Here is the Answer

Increase VPP voltage by 0.2V.

Path: Power setting>>Voltage>>VPP

Done!

Posted by: xhorsevvdi at 06:46 AM | No Comments | Add Comment
Post contains 43 words, total size 2 kb.

One customer asked how to cut by bitting on house keys using Xhorse Dolphin XP005L Machine.

Here is the Answer:

Dolphin XP005L mainly cuts car keys, so for house keys, Condor MINI PLUS II is a better choice.

But Dolphin XP005L can still cut KW1 house keys, here is how:

1)Under customize key data-share market and search kw1

2)Share market

3)I want to download

4)KW1

Done! Hope this helps!

Posted by: xhorsevvdi at 06:45 AM | No Comments | Add Comment
Post contains 80 words, total size 2 kb.

The latest V7.3.7 VVDI2 Software is released! Get the free download link from Xhorsevvdi.

1. Free Download VVDI2 V7.3.7 Software

V7.3.7 Software

2. V7.3.7 VVDI2 Update Info:

!!!Thisversionrequires firmwareV7.3.5!!!

Posted by: xhorsevvdi at 06:45 AM | No Comments | Add Comment
Post contains 172 words, total size 3 kb.

Question:

Xhorse VVDI PLUS PAD with Xhorse XDFAKLGL Cable,

To the new Mazda cx3 2020 To add a Smartkey will it fit? In this car it is not possible to read the OBD EEPROM, it is closed.

Answer:

Xhorse XDFAKLGL Ford Cable works on Ford AKL programming.

On Key Tool Plus, select "CX3 2017-" menu and perform add key function.

Done! Hope this helps!

Posted by: xhorsevvdi at 06:44 AM | No Comments | Add Comment
Post contains 75 words, total size 2 kb.

One customer gave feedback that his Multi Prog ECU Programmer was not powered on when reading Infineon MCU.

Here are some Answer:

Install driver and connect MULTI PROG

Path: Help>>Install Driver

*Select "CDC" if computer OS is win7

Done! Hope this helps!

Posted by: xhorsevvdi at 06:44 AM | No Comments | Add Comment
Post contains 52 words, total size 2 kb.

Question:

VVDI2+VVDI PROG, I have polo 2014 with eeprom 24c64 all key lost I read 24c64 and make service mode and when restore eeprom to dashboard and read IMMO data via obd I give that message always some problem with this tool. I m buy ID48 96Bit Copy for VW that I can learn key with all key lost which don't work every new day.

Here is the

Reason:

Select the wrong dashboard option in VVDI2 Programmer software.

Solution

Select "Auto Detect Type" to identify dashboard system and select the correct option for key programming.

Done! Hope this helps!

Posted by: xhorsevvdi at 06:43 AM | No Comments | Add Comment
Post contains 109 words, total size 2 kb.

One customer gave feedback that his Condor XC-MINI Plus II cutter broke before finishing key cutting.

Here are tests required by our tech.

Test main motor, all good.

Here is the Solution:

Open Condor Mini Plus II Machine and check connectors to the driver board.

Re-plug in four marked wires, and be careful about the wire marked by a yellow circle.

Done! Hope this helps!

Posted by: xhorsevvdi at 06:43 AM | No Comments | Add Comment
Post contains 75 words, total size 2 kb.

VVDI MLB Key now can be preordered! New stock will arrive soon!

Here are some tips about this new key,

1)Keys support Audi, Bentley, VW, Porsche, Lamborghini

2)Free data calculation in VVDI MLB/ Key Tool Plus

3)Generate remote on MLB Software in VVDI MLB/ Key Tool Plus

(In Stock) Xhorse XSMA41EN MLB Smart Remote:

https://www.xhorsevvdi.com/wholesale/xhorse-xsma41en-mlb-key.html

Done! Hope this helps!

Posted by: xhorsevvdi at 06:42 AM | No Comments | Add Comment
Post contains 68 words, total size 2 kb.

Questions:

My Multi Prog Programmer just won't read chips. Every MCU I ask to read reports that it doesn't recognize the chip.

Here is the Answer:

Check out wiring pinouts, and the marked wire should be VCC.

Done! Hope this helps!

Posted by: xhorsevvdi at 06:42 AM | No Comments | Add Comment
Post contains 52 words, total size 2 kb.

As the automotive security landscape rapidly evolves, Xhorse is once again setting a new benchmark with a groundbreaking update to its IMMO database, specifically targeting RENAULT and DACIA vehicles. This vital update empowers automotive locksmiths to provide their customers with the most reliable, cutting-edge security solutions available today.

2024.11.11
Groundbreaking Upgrades for RENAULT and DACIA
IMMO Database URTRADE
Key Tool Max Pro V54
Key Tool Plus V126

RENAULT
Smart Key
SCENIC 2016-
MEGANE 2015-
MEGANE SCENIC 2016-
QM6 (SAMSUNG QM6)
SM6 (SAMSUNG SM6)
TALISMAN 2015-
KADJAR 2016-
KOLEOS 2016-
ESPACE 2015-

Flip Key
MEGANE 2002-2008, 2008-2015, 2015-
SCENIC -2016, 2016-
MEGANE SCENIC 2002-2008, 2008-2015, 2016-
MODUS 2004-2012
CLIO 2006-2012
CLIO III
SM5 (SAMSUNG SM5) 2003-2004, 2005-2009
SM6 (SAMSUNG SM6)
SM7 (SAMSUNG SM7) 2003-2004, 2005-
QM6 (SAMSUNG QM6)
DUSTER 2014-2018, 2018-

KANGOO I
KANGOO II 2008-
KANGOO III 2020-
TRAFIC II Ph2
TWINGO I Ph3 2001-2006
SOLENZA
PRIMASTER
ESPACE 2015-
MASTER 2011-2016
KADJAR 2016-
TALISMAN 2015-
KOLEOS 2016-
SAFRANE 2009-
OROCH 2016-
ALASKAN 2016-
DOKKER
LOGAN 2010-2013, 2013-
SANDERO 2013-2020
LODGY
KWID (BRAZIL) 2023-2024
SYMBOL 2013-2018
TRIBBER 2014-2018
LAGUNA 2007-2011

DACIA
Flip Key
DOKKER
DUSTER 2014-2018
LOGAN 2010-2013, 2013-

LODGY
SANDERO 2013-

http://blog.xhorsevvdi.com/xhorse-vvdi-key-tool-plus-max-pro-immo-database-update-for-renault-and-dacia/

Posted by: xhorsevvdi at 06:41 AM | No Comments | Add Comment
Post contains 205 words, total size 3 kb.

GODIAG G-V ECU Cable is released!

It can work with VVDI Multi Prog to read TCU like DQ250, DQ200, MED17.5...

Here we are going to show you how to use this cable.

Tools:

VVDI Multi Prog Programmer

GODIAG G-V Cable

GODIAG ECU Adapter

Guidance:

Run Multi Prog software.

Search for and select "Audi A4 MED17.5".

Connect MED17.5 to Multi Prog by wiring diagrams.

Read EEPROM and turn on GPT adapter and activate 120ohm resistor.

Read FLASH.

Done!

Posted by: xhorsevvdi at 06:40 AM | No Comments | Add Comment
Post contains 88 words, total size 3 kb.

One customer gave feedback that Dolphin XP005 Machine would not hold his keys tightly. He wondered if the keys were not supported or other clamps are required.

Here is the Answer:

If the keys are too short, Dolphin XP005 Key Cutting Machine will barely hold them tightly.

In this case, users can use Clamp M1, or

Try to wrap some tape around the base of the key but be careful during it is being cut.

Done! Hope this helps!

Posted by: xhorsevvdi at 06:40 AM | No Comments | Add Comment
Post contains 89 words, total size 1 kb.

GODIAG GT107+ & GPT Boot& G-V ECU Cable work with Xhorse multi prog for easier connection.

Here is the connection diagram:

1. To read DQ200 with Xhorse MULTI PROG & GT107+ &G-V ECU Cable

2. To read DQ250 with Xhorse MULTI PROG & GT107+ & G-V ECU Cable

3. To read DQ200 with Xhorse MULTI PROG & GT107 & G-V ECU Cable

4. To read DQ250 with Xhorse MULTI PROG & GT107 & G-V ECU Cable

5. To read ME17.8.8 with Xhorse MULTI PROG & GODIAG ECU GPT Boot AD Programming Adapter & G-V ECU Cable

6. To read MED17.5 with Xhorse MULTI PROG & GODIAG ECU GPT Boot AD Programming Adapter & G-V ECU Cable

http://blog.xhorsevvdi.com/xhorse-multi-prog-and-godiag-gt107-gpt-boot-g-v-ecu-cable-connection-diagram/

Posted by: xhorsevvdi at 06:39 AM | No Comments | Add Comment
Post contains 131 words, total size 3 kb.

One customer asked if Key Tool Plus with xndp30 adapter will read edc17c50. And is BMW Bench Read ISN License needed?

Here is the Answer:

Yes and no license is required.

Here are how to connect edc17c50,

Users can use

XDNP30 BOSCH ECU Adapter or

VVDI Prog BOSCH ECU Adapter with XDKP30 Adapter

Done! Hope this helps!

Posted by: xhorsevvdi at 06:38 AM | No Comments | Add Comment
Post contains 68 words, total size 2 kb.